Grip Varmeveksler GH08 Trykkbryter

[Quantity / Component]
Grip heater main body, Spacer for installation, Electra-tap, Cable tie, Instruction manual

[Color / Material]
Electrically heated rubber grips: Black

[Shape / Type]
For 1" handles: 25.4mm
Slim electric heating grip

[Size]
Grip Length: 131mm
Grip Internal Dimensions: 127mm
Grip Max Diameter: 37mm

**The stock optional grip heaters manufactured by Honda have a half-wound heating wire, but this product has a full-wound heating wire.The power consumption is higher than that of Honda's optional grip heaters, and starting and using the grip heaters at max heat immediately after engine startup will significantly drain the life of the on-board battery.The life of the battery and electrical system will be extended if the bike is sufficiently ready for startup after the engine has been started, idled, and run 2-3 km.
*Since motorcycles are not power generators, do not use them recklessly. Instead, use the surplus electrical power of the motorcycle gradually. This approach is gentle on the motorcycle.Also, please consider the use of a handlebar cover to increase the overall effect of thermal protection and warmth under low power use.Since the wind blows on your hands and they get cold, if you can physically block the wind, your hands will be less likely to get cold and heat will accumulate.
*With the recent trend toward expansion of electrical components, we have heard from many customers that only the grip heater option is not enough.Motorcycles move by burning fuel, and their explosive power is also used to generate electricity, powering various electrical equipment. Therefore, when considering installation, it is important to first discuss with your bike shop about the essential and preferable options for your bike's electrical accessories. We kindly ask for your careful consideration after consulting with the shop before proceeding with the installation.
*The power demand is so high that even if the system can be used at level 5 of the 5 maximum heat levels when riding on highways or expressways, the battery protection function may automatically stop the power supply when the bike is stopped in traffic jams or at traffic lights.In such a case, please make sure to start up and use it again after reaching cruising speed.
*When installing on a stock or aftermarket throttle tube, it is recommended to warm up the throttle tube before installation to allow for thermal expansion and easier installation.
*Full cowl bikes and scooters may require more labor and may require a longer period of time since the wiring cowl will be threaded during installation.Also, since it is an electrical component, the location for supplying electricity may vary depending on the bike for the optional coupler or surplus wiring. Even if the grip length that can be installed is long, if the wiring work for supplying power is technically difficult and cannot be installed during storage, it could be a problem.Before proceeding, please consult with the bike shop in advance and consider it.
Regarding the corresponding throttle pipe, please thoroughly check the condition of the stock parts and the stock part number. Also, carefully consider that depending on the length of the grip heater, it may not be possible to use stock bar ends.
*In recent times, there has been remarkable progress in motorcycle equipment, and many bikes are now equipped with high-quality components such as heated grips as standard features upon delivery.In this case, please confirm not only this compatibility data but also the actual condition of the bike with the bike dealer.
*If you install this product on a motorcycle with low power generation, it will be difficult to warm up and the battery will be drained.
*In some injection vehicles, the power is controlled by a computer, and if there is an overcurrent in the power supply, the power is cut.Choose the wire without limit of power.
*Please be careful to connect to vehicles with LED taillamps and vehicles with anti-theft function such as immobilizer.
*Do not connect to thin wires such as LED lamps.This may cause abnormal overheating of the wiring.
*Please pay attention to the wiring around the key cylinder especially when the vehicle is equipped with immobilizer.
*This may cause the immobilizer to malfunction or the computer to fail.
*This product is a consumable item. Please replace the heat sheet when the surface of the heat sheet is scratched, cracked or worn.
*Before installing, turn on the power of the grip heater to heat the grip heater, which makes it easy to install it because it will expand in volume.
*There is a case that this product, which is a universal product, is difficult to fit or is loose depending on the vehicle that uses an inch handle.In this case, it is necessary to modify the handlebars according to each vehicle (shave the mounting surface to fit the grip, increase the bulk of the handlebars to eliminate the looseness between the handlebars and the grip).
*Battery consumption is particularly high for Harley-Davidson, so please pay special attention to battery drainage when using this product.
*Please do not activate the grip heater immediately after the engine is started, but after 5-10 minutes of warm-up operation.
*Voltage consumption: 21W (level 1) -36W (level 5) at voltage 13.5V
*Some motorcycles are designed to automatically supply electricity to other electrical systems when the accelerator is opened.In that case, the voltage may drop and the grip heater may stop operating.
*This product requires the removal of the stock grip and throttle cone if necessary, and modification of the power supply wiring from a location where voltage can be secured, so if you are unsure, it is recommended that you ask your nearest authorized dealer or vehicle dealer to do the work.
*Images may contain other products.
*There may be changes in product specifications due to the manufacturer's reasons.
.