Det er et veldig kraftig U-formet lås som vedtok en kraftig stållegeme og en sterk nøkkelfat.
Fast kan festes til dekk, hjul, etc.
Selvfølgelig kan du bruke det ikke bare for motorsykkel, men også for sykler etc.
Når det oppdager vibrasjon, lyder PierceAlarm-lyden av stort volum på 120 dB, og det er et produkt som demonstrerer kraft for å forhindre tyveri av en bil som du ønsker.
Med vanntett spesifikasjon, er Disc Lock Body ferdig med luksuriøs finish ved å bruke spesiell overflatebehandling.
For AlarmBattery vedta CR2Lithium batteri. (Kan brukes i ca 10 måneder)
Også, Alarm [PÅ AV] Den har en funksjon.
------ Metode for drift ------
[ON / OFF bytte metode]
Vri nøkkelen (Ca 270 grader) Når du låser og returnerer nøkkelen bakover "Pi" Hvis det bare er en kort varslingslyd, piper et varslingslyd etter noen sekunder at sikkerhetsalarmen har slått PÅMODE.
Ved å gjenta samme operasjon raskt igjen etter å ha utført operasjonen for å slå på "Pippidi" og to korte pip, er sikkerhetsalarmen slått av på dette tidspunktet.
* Når du låser nøkkelen, må du sjekke operasjonslyden og låse den.
[Batteri Installasjonsmetode]
* Phillips Skrutrekker er nødvendig i tillegg til tilleggsverktøyet.
1. Fjern låsestangen.
2. Sett Phillips skruetrekkeren inn i låsehullet og fjern skruen.
* Fjern skruen som ikke har nøkkelsylinderen.
3. Fjern SiliconCover, Cover, AlarmUnit i denne rekkefølgen.
4. Skrik av AlarmUnit (2 steder) Med det vedlagte verktøyet.
5. Fjern batteridekselet, dekselet og vanntett deksel og installer batteriene.
6. Den er ferdig med omvendt prosedyre.
* Når du installerer batterier, vær forsiktig så du ikke legger til vanntett deksel.
* AlarmUnit Ved installasjon, vær oppmerksom på utsnittet av AlarmUnit og sett det inn.
This is a very strong U-shaped lock with a strong steel body and a strong key barrel.
It can be tightly fixed to tires and wheels.
Of course, it can be used not only for motorcycles but also for bicycles.
When vibration is detected, a piercing alarm sounding at a loud volume of 120dB is emitted, and this product is effective in preventing theft of your vehicle.
In addition to waterproof specifications, the body of the disc lock is finished with a special surface treatment to give it a high-class look.
The battery for alarm is CR2 lithium battery.(It can be used for approx. 10 months)
In addition, the alarm has an [ON / OFF] function.
--- Operation ---
[How to switch ON / OFF]
When the key is turned (approx. 270°) to lock and then turned back, a short "beep" sound will be heard once, followed a few seconds later by a notification sound indicating that the security alarm has entered the ON mode.
By repeating the same operation quickly again after turning on the device, you will hear a short "beep" sound twice.In this case, the security alarm is turned off.
*When you lock the key, please confirm the sound of operation and lock the door.
[How to install the battery]
*A Phillips screwdriver is required in addition to the supplied tools.Please be prepared.
1. Remove the lock bar.
2. Insert a Phillips screwdriver into the hole of the lock bar and remove the screw.
*Remove the screw from the side without the key cylinder.
3. Remove the silicone cover, cover, and alarm unit in that order.
4. Remove the two screws from the alarm unit with the supplied tool.
5. Remove the battery cover and waterproof cover and install the battery.
6. Assemble in reverse order to complete.
*Please be careful not to forget to attach the waterproof cover when you install the battery.
*When installing the alarm unit, be careful to insert it into the notch on the alarm unit.