Clutch Holder Fook-Type
Produkt nr. 1900
162.17 NOK (2,256 JPY)
Listepris: 176.69 NOK Lagre 8%
+23 Webike punkt (1.65 NOK)
Produkt nr. 1900
162.17 NOK (2,256 JPY)
Listepris: 176.69 NOK Lagre 8%
+23 Webike punkt (1.65 NOK)
3.6 / 5
8 anmeldelser
[How is it used?
TZr250R (3XV) I bought this to Rose the Clutch of
Universal's Clutch holder is available from several manufacturers, but I chose this product which was relatively inexpensive.
Was the one you received as per Image?
It's no surprise since it keeps the Clutch down, but it was much bigger than I imagined.
There was no deformation, and the production seemed to be good.
How was your experience with it?
I used it for the first time so I had to watch and learn, but it was surprisingly easy to fix.
I was worried because there was an imprecation that it could not be fixed, but I did not have any problem.
However, I was a little worried because the hook was shallow, probably because of Universal.
[Points to note]
It is important to note that depending on the motorcycle, there is a possibility that the hook may be shallow or not hooked.
【Review】
The tool is only used to hold down the Clutch, but it made the job easier.
It's not that expensive, so it's handy to have one if you're rooting an engine.View Detail
[How is it used?
I used this to replace the Clutch boss on my MT-07.
Was the one you received as per Image?
This is a general Clutch holder. There are several companies that sell the same shape.
How was your experience with it?
The pawl tip format is bad, and when Torque is applied, the Y-shape spreads and the pawl comes off. There is a screw type stopper to control the spread, but it is defeated by Torque.
The reason it spreads is that the tip of the nail is cut at an angle to fit easily into the groove of the Clutch boss.
I had to tighten the Stopper with a water pump ply shop to get it to work. I don't think that's the way it should be used.
[Points to note]
The Clutch boss has a high fastening torque, so if it comes off you could get hurt.View Detail
MINIMOTOMinimoto Clutch Holder Fook-Type Commercial Product No : It is 1900. We purchased TZr 250 for Clutch disassembly. OEM purchased because there was no stock. Especially served without problems.View Detail
I purchased it because I felt the necessity for overhauling the Engine
Let's use exclusive items as we can forcibly substitute other products for damaging parts
It is better to be cheap
Because there seems to be no use of Others, it is regrettable that there is a high possibility of being a fertilizer for Chest once usedView Detail
It is a nail type Universal holder.
Since an Impact also carries out Torque management with the last Torque wrench at attachment when removing, the surroundings stop of a Clutch center requires this Type of Holder.
If a 1-time limitation or -- is thought since it is too cheap, anticipation is betrayed and it can use perfectly.When carrying out a Friction-plate addition by Clutch strengthening of Scorpa, it used, but there are likely to be other uses.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Melding
Velg alternativ før legge i handlekurven.
BESTILLINGER
INFORMASJON
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.